Egg Drop Challenge

 PRACTICAL 5: Egg Drop 3D Printing Challenge🥚

For this practical, we were tasked to come up with a design which can protect a quail egg from a fall from roughly 2 meters high.

There are 2 parts to our design, my teammate Ruba and I decided to split up the design so we can design the parts separately. She designed the outer frame while I did the inner casing.

This was our initial design (for inner casing) : 


Cross sectional view:

Inner casing which uses a screwing mechanism, and the quail egg will be loaded in the middle:


Outer frame where the inner casing will hang from the tab: (my teammate Ruba designed this 😻)

Sketch of our initial design:


However, we scrapped 😓 our initial design (the inner casing) as the screwing mechanism was not cleanly printed. We kept the outer frame 👍


We then decided on a box design with a T-shaped door instead (for the inner casing)
Function of the T-shaped door: to keep the quail egg in the box so that it will not fall out middrop.



The T-shaped door will fit into the slot like this:

This is how our final product looks like after connecting the inner casing and outer frame.
The outer casing (brown part) was supposed to be hollow but we decided to left the printing supports on so that more impact can be absorbed and the frame will be more rigid 💪


Video of our drop: 

There were a few cracks on the shell upon closer observation, but the egg did not break!! 👻


To prove that the egg we used is raw, I cracked it open and cooked it HAHHAHA 🍳😎
(notice that the cracks and patterns on the egg shell are the same as shown in previous pic)


rest in pieces, egg 👀

Hero shot after the drop:


Guide on 3D printing

After the design was completed on Fusion360, right click on the design body and save it as an STL file.

Click "Save as mesh":

Change the format to "STL (Binary):

After clicking "OK" for the previous step, now click "Save".

Open the STL file from Downloads

Click on the arrow on the top right hand corner to change the infill density according to your needs. Supports can also be opted for.


"Slice" on the bottom right corner the process to view the printing duration.

Select the printer that will be used.

I also changed the printer settings according to printer settings in the lab.

The printing speed can also be changed.

Insert a thumb drive and click "Save to Disk". The file will be saved as a G-code file.


From downloads again, save the file into the thumb drive.

Next, insert the thumb drive into the printer and start printing after the printer has been prepped.

To prepare the printer:

1. Turn on the printer

2. Prepare the filament by placing it into the container and make sure that it has been heated up to around 50 degree celcius for an hour.


3. On the control screen, select "control" and "preheat PLA settings". Change the nozzle temperature to 200 degree celcius and the bed temperature to 65oC. 

4. Once the temperature settings have bene reached, insert the filament into the nozzle by clamping the spring behind the nozzle.

5. Now that the filament is ready, use a brush to dust the surface of the printing bed so that it is clean. 
6. From the main menu on the control screen, select the file that should be printed under the "Print" section. 
7. After printing has been started, this should show up on the control screen. The settings for the bed and nozzle temperature can still be changed if they are not correct.


8. When the design is done printing, leave it on the bed to cool down before removing it *carefully. Brush off the excess filament that may be present on the bed using tools in the lab, eg. brush & scraper.

Printing time lapse: (T-shaped door)




Reflection 🖉
This practical took the longest to complete, mainly due to the trail and error stage where we messed up quite a few times on the dimension for both the inner and outer frame. However, I still had fun ✌working with my teammate. It was our first time using a 3D printer and it definitely opened our eyes on how versatile 3D printing can be. 

I also got to explore more of Fusion360 on myself and learned a few new things. For example, I came across a function called "Spline" which allows us to draw a smooth curved surface. I also learned about the "Thread" function which allowed me to create a screwing mechanism for my initial design. I have never heard or used these functions before never knew sketching on CAD software is just as flexible as sketching on a piece of paper. 





Comments